7 Years Lifetime Wireless Fire Carbon Monoxide Detector Alarm Smoke Detector With AA Battery

7 years lifetime Wireless Fire Carbon Monoxide Detector Alarm Smoke Detector With AA Battery
 
Product Introduction
 
Carbon Monoxide Detector(CO detector), use of high quality electrochemical sensors, combined with advanced electronic technology and sophisticated technology made of a stable work, long life and other advantages; can be placed on the ceiling or wall mount and other installation methods, simple installation, easy to use; Where carbon monoxide gas is present, once the concentration of carbon monoxide gas reaches the alarm setting value, the detector will emit an audible and visual alarm signal to remind you to quickly take effective measures to effectively avoid the occurrence of fire, explosion, suffocation, death and other malignancies.
 
WARNING: Exceeding the temperature and humidity allowable range may reduce or lose the
detection function.
 
Specification
 

 
Operation Instructions
 
(1)The battery is correctly loaded into the detector with positive and negative polarity, The buzzer emits a "beep" sound and the detector starts to warm up for 40s. the LCD screen displays the count down, at this time, the detector has no detection function; after 40s, The detector enters the normal monitoring state and the LCD screen is normally closed. When the measured value of the measured gas in the air is bigger than 20×10-6, the LCD displays the real-time concentration of the measured gas in the environment.
 
(2)When the concentration of the measured gas in the environment reaches the alarm setting value, the detector emits an audible and visual alarm indication.
 
(3)Green power indicator, flashing once every 35 seconds, indicating that the detector is working.
 
(4)Red alarm indicator. When the detector enters the alarm state, the red alarm indicator flashes rapidly and the buzzer sounds at the same time. The alarm of the alarm signal makes four cycles, each cycle is 100ms on/100ms off. Then turn off for 2 seconds until the CO concentration drops below the alarm setting value.
 
(5)This CO alarm has an automatic self-test function to detect any failure of hardware, which is performed about every 1 minute in normal standby status.
 

How To Install The Co Alarm
 
This CO alarm is powered by three LR6 AA batteries and requires no additional wiring. Make sure the alarm can be heard from all sleeping areas or place several alarms.Install the alarm in places easy to test and operate and to replace batteries. At the time of fixing the alarm on the wall, the installation height must be over 1.5m and 0.3m lower than the ceiling, with 1.5m away from room corners, wall edges and large furniture.
 
Wall Mounting Installation Steps
 
1)Having established the mounting location ensure that there is no electrical wiring or pipe work in the area adjacent to the mounting surface.
 
2)Mark the two mounting hole locations in a wall 5.5cm (2.165in) and drill holes in the marked position. Insert wall plugs into the holes.
 
3)Lock the mounting bracket with the screws. Tighten the screws properly.
 
4)Insert three AA batteries in the battery compartment with correct polarity mark on the rear of the detector. After a beep, close the battery cover, and then test whether the alarm is functioning properly by press the “TEST” button on the flank of the detector to make sure it is normal functioning.
 
5)Clip in the alarm into the mounting bracket.
 
CAUTION: for safety of the user the CO alarm cannot be mounted without its batteries. When replace the battery, test the alarm to make sure it is normal functioning.
 

 
Package includes
 
1 × Carbon monoxide alarm
1 × Mounting bracket
1 × Screw Kit
1 × User manual

 
FAQ
Q:How about the quality of Carbon Monoxide Detector Alarm?
A :We produce every product with good quality materials and fully test three times before shippment. What is more, our quality areapproved by CE RoHS SGS & FCC, IOS9001, BSCI.
Q: Can i have a sample order?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q: What is the lead time?
A: Sample needs 1 working days, mass production needs 5-15 working days depends on order quantity.
Q: Do you offer OEM service, like make our own package and logo printing?
A: Yes, we support OEM service, including customizing boxes, manual with your language and printing logo on the product etc.
Q: Can I put order with PayPal for a fast shipment?
A: Sure, we support both alibaba online orders and Paypal, T/T, Western Union offline orders. Please contact us for details.
Q: How do you ship the goods and how long does it take arrive?
A:We usually ship by DHL(3-5days), UPS(4-6days), Fedex(4-6days), TNT(4-6days), Air(7-10days), or by sea(25-30days)at your request.